Close
Search
Banner Banner
Products
請選擇分類
TAKEX_FZV8301BC

3 mm Slim Convergent Reflective Fiber Optic Unit

  • The TAKEX FZV8301BC convergent reflective fiber optic unit has a head just 3 mm thick for substrate detection on a robot end effector. With an F70R and a 50 × 50 mm clear glass plate, its range is 0–20 mm. The 2 m fiber can be cut to length and needs a bend radius of at least 20 mm.
  • Brand TAKEX Takenaka Engineering Co., Ltd.
Features
  • 3 mm sensing head: The 18 × 10 × 3 mm head fits into a robot end effector to check for substrate presence at the pickup or placement position.
  • Single-sided sensing: Light is transmitted and received through the same window near the front of the head. Aim the window at the substrate to detect reflected light within the sensing zone.
  • 0–20 mm reference range: With an F70R amplifier and a 50 × 50 mm clear glass plate, the detecting distance is 0–20 mm. Use this range when planning the window-to-substrate spacing.
  • Two M3 mounting holes: The through holes are on 7 mm centers. Use this pattern to design the mounting bracket and keep the front sensing window clear.
  • 2 m cut-to-length fiber: The Ø1.25 mm cable can be trimmed to fit the route from the head to the amplifier. Allow a bend radius of at least 20 mm.
Specification
ItemSpec.
ModelFZV8301BC
Detection methodConvergent reflective
Sensing head, length × width × thickness (mm)18 × 10 × 3
Sensing head materialBlack anodized aluminum
Mounting holes2 M3 through holes
Mounting hole center spacing (mm)7
Reference target with F70R50 × 50 mm clear glass plate
Detecting distance (mm), F70R / F70AR0–20
Detecting distance (mm), F80R long-distance / high-speed modes0–20
Detecting distance (mm), F85RN long-distance / high-speed (H-SP) modes0–20
Detecting distance (mm), F100R long-distance / high-speed modes0–20
Detecting distance (mm), XF12R-A Long / H-SP modes0–20
Detectable object diameter, min. (mm, excludes F71R)Φ0.015
Fiber length (m)2, cut to length
Cable diameter (mm)Φ1.25
Core diameter (mm)Φ0.75
Allowable bend radius, min. (mm)20
Jacket / core materialPolyethylene / plastic
Fiber optic unit ambient temperature (°C)−30 to +70

Specification notes

  • Measure the gap from the sensing window to the substrate surface. If the production substrate has a different material or finish from the reference glass plate, check detection with a sample at the intended gap.
  • Use reduced sensitivity with the F70R, F70AR, F80R, F85RN, or F100R. Check the amplifier output with the substrate present and again with it removed.
  • Lay out the fiber before cutting it. Allow a bend radius of at least 20 mm where it leaves the head, passes through clips, or turns in a cable channel.
FAQ

Q1: Is the FZV8301BC a fiber optic unit or a sensor with a built-in amplifier?
A: It is a convergent reflective fiber optic unit consisting of a sensing head and fibers. A separate fiber amplifier processes the received light and provides the detection output.


Q2: Where can I mount the head to detect a substrate on a robot?
A: Recess the 3 mm head into the end effector with its window facing the substrate. The head sends and receives light from one side, leaving the other side accessible to the handling mechanism.


Q3: What dimensions do I need to design the mounting bracket?
A: The head measures 18 × 10 × 3 mm and has two M3 through holes on 7 mm centers. Keep the sensing window clear and leave room for the fibers to exit the back of the head.


Q4: What target gives the 0–20 mm range with an F70R amplifier?
A: The FZV8301BC has a 0–20 mm detecting distance with an F70R and a 50 × 50 mm clear glass reference plate. Use a production substrate to confirm the working gap for your application.


Q5: Does the range change between high-speed and long-distance modes on the F80R?
A: Both F80R modes specify 0–20 mm with the FZV8301BC. A working gap greater than 20 mm exceeds the specified range for this combination.


Q6: How should I set the amplifier sensitivity during setup?
A: Use reduced sensitivity with the F70R, F70AR, F80R, F85RN, or F100R. Place and remove a substrate at the actual handling position and check that the output switches between the two states.


Q7: Can I shorten the 2 m fiber, and how much space do bends need?
A: Yes. Plan the route with a bend radius of at least 20 mm, then trim the fiber at the amplifier end. R20 refers to the radius of the bend.


Q8: What does the Ø0.015 mm specification mean?
A: It is the min. detectable object diameter and excludes the F71R amplifier. To determine whether a particular glass thickness can be detected, test a sample of that glass.


Q9: What ambient temperature can the fiber unit handle near a heat source?
A: The FZV8301BC is rated for −30 to +70 °C. Check the ambient temperature at the head and along the fiber route, and select the amplifier location using its own temperature rating.


Q10: How do I choose between the FZV8301BC and the FZV8203BC in a tight space?
A: Choose the FZV8203BC if the recess only takes a 2 mm head and the fiber can follow a 30 mm bend radius. If a 3 mm head fits but the route allows only a 20 mm radius, choose the FZV8301BC. With an F70R and a 50 × 50 mm clear glass plate, the ranges are 0–19 mm for the FZV8203BC and 0–20 mm for the FZV8301BC.

0
Go top