Close
Search
Banner Banner
Products
請選擇分類
TAKEX_GTSH705V

Pin-Coupled Vacuum Through-Beam Fiber Units

  • TAKEX GTSH705V (0.5 m) and GTSH710V (1 m) are vacuum through-beam fibers with M4 right-angle heads for single-channel feedthrough pins. The 350°C head-side sections measure 400 and 900 mm, respectively. Both have a 100 mm, 200°C pin-side section and reach 950 mm with an F100R in long-distance mode.
  • Brand TAKEX Takenaka Engineering Co., Ltd.
Features
  • Single-channel optical feedthrough: A feedthrough pin connects the vacuum-side fiber to the air-side fiber through the chamber wall. Both models are rated for vacuum levels down to 1 × 10⁻⁸ Pa.
  • Right-angle M4 sensing head: The head has a 12 mm long M4 × 0.7 mm threaded section. The cable exits perpendicular to the sensing axis so it can run alongside the fixture.
  • Two lengths for heated sections: The head-side section rated to 350°C measures 400 mm on the GTSH705V and 900 mm on the GTSH710V. Both have a 100 mm section rated to 200°C at the feedthrough end.
  • Range by amplifier mode: With an F100R, either fiber reaches 950 mm in long-distance mode and 380 mm in high-speed mode. With an F85RN, the ranges are 800 mm in long-distance mode and 200 mm in H-SP mode.
  • Wafer detection in vacuum chambers: Aim the transmitting and receiving heads at the same point on the wafer in a V configuration. This convergent reflective arrangement reduces the influence of background reflections.
Specification
ItemSpec.
ModelsGTSH705V
GTSH710V
Detection methodThrough-beam
Location and connectionVacuum side, single-channel optical feedthrough pin
Vacuum rating (Pa)1 × 10⁻⁸
Vacuum-side fiber length L (m)GTSH705V: 0.5
GTSH710V: 1
Head-side section L2 length (mm, 350°C max.)GTSH705V: 400
GTSH710V: 900
Pin-side section L1 length (mm, 200°C max.)100
Sensing head shape and threadRight-angle, M4 × 0.7 mm
Threaded head length (mm)12
Formed elbow radius (mm)10
Sensing face to cable centerline (mm)29.5
Sensing head axis to start of spiral tubing (mm)27
Protective tubingStainless steel spiral tube, Φ2.9 mm OD
Pin-side locking ring (OD × length, mm)Φ8 × 9
F100R detecting distance, long-distance mode (mm)950
F100R detecting distance, high-speed mode (mm)380
F85RN detecting distance, long-distance mode (mm)800
F85RN detecting distance, H-SP mode (mm)200
F80R detecting distance, long-distance mode (mm)500
F70R / F70AR detecting distance (mm)280
XF12R-A detecting distance, long-distance mode (mm)370
XF12R-A detecting distance, H-SP mode (mm)150

Specification notes

  • Check the cable route and the location of the heated zone. The additional 500 mm on the GTSH710V is in the head-side L2 section. The pin-side L1 section remains 100 mm long.
  • For fixture layout, measure 29.5 mm from the sensing face to the cable centerline and 27 mm from the sensing head axis to the start of the spiral tubing. These dimensions are perpendicular to each other.
  • The listed detecting distances apply when the transmitting and receiving heads face each other. In the V-shaped wafer detection setup, the two optical axes meet at the wafer surface.
FAQ

Q1: Where do the GTSH705V and GTSH710V go in a vacuum system?
A: Both fiber units go inside the chamber. An FA7VP-M5 optical feedthrough pin connects the vacuum-side fiber to an air-side fiber, which runs to the amplifier outside the chamber.


Q2: How do I choose between the GTSH705V and GTSH710V?
A: Measure the route from the feedthrough pin to the sensing head and identify how much of it runs through the heated zone. The 0.5 m GTSH705V has a 400 mm section rated to 350°C. The 1 m GTSH710V provides 900 mm at that rating.


Q3: Can the fiber section next to the feedthrough pin withstand 350°C?
A: The 100 mm L1 section next to the feedthrough pin is rated to 200°C on both models. The 350°C rating applies to the L2 section at the sensing head.


Q4: Which dimensions should I check when designing the mounting fixture?
A: The M4 × 0.7 mm thread is 12 mm long. To locate the cable exit, allow for 29.5 mm from the sensing face to the cable centerline and 27 mm from the sensing head axis to the start of the spiral tubing.


Q5: What does R10 mean on the dimensional drawing?
A: R10 marks the 10 mm radius of the formed elbow. Use it to check clearance around the sensing head. The allowable cable bend radius is a separate routing specification.


Q6: Which amplifier and mode provide a 950 mm through-beam range?
A: Use an F100R fiber amplifier in long-distance mode with either fiber unit for 950 mm. Switching to high-speed mode gives a range of 380 mm.


Q7: With an F85RN, does the 1 m fiber increase the sensing range?
A: Both fibers provide 800 mm in long-distance mode and 200 mm in H-SP mode with the F85RN. The 1 m GTSH710V lets you route the cable to a sensing point farther from the feedthrough pin.


Q8: Which fiber in the system can be cut to length?
A: The FT7VBC-M5 is a 2 m air-side fiber that can be cut to length between the feedthrough pin and the amplifier. For the vacuum-side route, choose the 0.5 m GTSH705V or the 1 m GTSH710V.


Q9: How does the cable exit differ between the GTSH and GTH fiber units?
A: The GTSH705V and GTSH710V have right-angle heads that route the cable to the side. The GTH705V and GTH710V have straight heads with an axial cable exit. Choose the head that fits the space beside or behind the mounting fixture.


Q10: How are the GTSH fibers arranged to detect a wafer in a vacuum chamber?
A: Place the transmitting and receiving heads on the same side of the wafer. Aim them at the same point from different angles to form a V. The receiver collects light reflected from the wafer, reducing the influence of background reflections.

0
Go top